ZL8800 - Input Current Measurement Capability - Part 3

Added on November 08, 2013
Understanding how the ZL8800 measures input current and how it can monitor efficiency of a two-phase device.

Related Videos

Play Video
1:40
Identifying the differences between the ZL8800 and ZL8801 dual phase PMBus™ ChargeMode™ control DC/DC digital controllers.
Play Video
5:08
Intersil's new ZL8800 with ChargeMode control loop technology provides full telemetry and superior stability.
Play Video
4:54
Learn how Intersil's proprietary ChargeMode Digital Control Loop delivers superior stability, eliminating the need for any compensation.
Play Video
4:07
Understanding how the ZL8800 measures input current and how it can monitor efficiency of a two-phase device.
Play Video
10:55
See how Intersil's ZL8800 provides continuous, output current measurements without any additional components.
Play Video
7:21
Overview of how the ZL8800 works, and how its unique design enables responding to transients in a single cycle.
Play Video
2:33
Learn about all the different types of fault protections available with Intersil's new ZL8800.
Play Video
2:45
Learn how to set up voltage monitoring along with warning and fault levels for both overvoltage and undervoltage through PMBus.
Play Video
2:36
Learn how Intersil's new ZL800's ADC monitors the entire output current waveform.
Play Video
1:40
Identifying the differences between the ZL8800 and ZL8801 dual phase PMBus™ ChargeMode™ control DC/DC digital controllers.
Play Video
5:08
Intersil's new ZL8800 with ChargeMode control loop technology provides full telemetry and superior stability.
Play Video
4:54
Learn how Intersil's proprietary ChargeMode Digital Control Loop delivers superior stability, eliminating the need for any compensation.
Play Video
4:07
Understanding how the ZL8800 measures input current and how it can monitor efficiency of a two-phase device.
Play Video
10:55
See how Intersil's ZL8800 provides continuous, output current measurements without any additional components.
Play Video
7:21
Overview of how the ZL8800 works, and how its unique design enables responding to transients in a single cycle.
Play Video
2:33
Learn about all the different types of fault protections available with Intersil's new ZL8800.
Play Video
2:45
Learn how to set up voltage monitoring along with warning and fault levels for both overvoltage and undervoltage through PMBus.
Play Video
2:36
Learn how Intersil's new ZL800's ADC monitors the entire output current waveform.
Play Video
1:40
Identifying the differences between the ZL8800 and ZL8801 dual phase PMBus™ ChargeMode™ control DC/DC digital controllers.
Play Video
5:08
Intersil's new ZL8800 with ChargeMode control loop technology provides full telemetry and superior stability.
Play Video
4:54
Learn how Intersil's proprietary ChargeMode Digital Control Loop delivers superior stability, eliminating the need for any compensation.
Play Video
4:07
Understanding how the ZL8800 measures input current and how it can monitor efficiency of a two-phase device.
Play Video
10:55
See how Intersil's ZL8800 provides continuous, output current measurements without any additional components.
Play Video
7:21
Overview of how the ZL8800 works, and how its unique design enables responding to transients in a single cycle.
Play Video
2:33
Learn about all the different types of fault protections available with Intersil's new ZL8800.
Play Video
2:45
Learn how to set up voltage monitoring along with warning and fault levels for both overvoltage and undervoltage through PMBus.
Play Video
2:36
Learn how Intersil's new ZL800's ADC monitors the entire output current waveform.

 


Video Transcript

In this video we're going to talk about the input current measurement capability of the ZL8800. Now the ZL8800 is a two-phase or a dual output device. But you do get one input current measurement per chip. So what this means is, if you're using a two channel output, you're just going to get a single measurement. But in a two-phase application, now you can actually use that current measurement to monitor the efficiency of the device.

The way it works and is implemented is, it's just a shrunt resistor that's used. This is going to be a small, couple milliohm resistor. Now the thing you have to be careful of is the maximum voltage, you can see across the input for the differential sensing, is 20 millivolts. So you need to make sure that you calculate your input current and the resistor appropriately such that you're always below 20 millivolts if you want to get the reading.

Quick way of doing this, just calculate what your output power is and use a worst case efficiency for max load and then from that you can size approximately the input resistor. If you don't wish to use this function, you can just tie these two pins, the I-IN positive and the I-IN negative to the V-IN. One practical consideration you may want to take in mind is, placing this resistor before you have any of those high-frequency ceramic capacitors for bypassing. Because when this hi-fi switch turns on, you're getting a lot of AC current circling through those CADs. This resistor, what you really want by placing before, is you see the average current coming in.

Now we can go to the bench and take a look at the GUI on how this input current measurement is taken and what results we see.

So let's do a demonstration showcasing the ZL8800 with an input current measurement. This is the dual phase board for the ZL8800. So it's using both of the channels tied together at a single output, to create a two phase solution. You'll notice on the board, we have a resistor that's placed here near the input. This is the current sense resistor that is used to measure the input current. It's a five milliohm resistor and we're just measuring the voltage drop across it with internal ADC.

So right now as you can see with the GUI, we're using a 12-volt input, a 1.2-volt output and we don't have any load currents. Now as you start loading it down, you'll see in the GUI, the load current will change and also the input current will change. So let's put a five amp load on. And right away in the scope, we have a current probe connected to the output device and you can see that load current starts increasing and the input current will increase by a small amount also. It's fairly linear so as we keep increasing the load, we'll accurately be able to track that and the input current should follow it roughly the same.

So let's move up to 10 amps. You can see the output current is about five amps per division on the scope, so we're pulling about 10 amps load right now and the input current is following it commensurately. I can keep increasing it. I can go way up to 20 amps. And once again we get accurate tracking with the GUI and the input current is accurately tracking also.

Now you notice the input current doesn't appear to be quite linear, that's because as we increase the load current, we're actually moving up the efficiency curve. So we're moving from maybe 82% to 85% to 90% as we start moving across the load range, because this part's really optimized for high efficiency between 20% to about 80% of full load.

This evaluation board is capable of doing up to 60 amps. It's designed to do 30 amps per channel, and once again as they're combined, it means a total output capability of 60 amps. For more information, please continue watching the remaining videos or you can evaluate your own ZL8800 by getting an evaluation board from intersil.com