Evaluating the ISL95338 USB-C Buck-Boost Regulator

Added on October 09, 2017
Learn how to set up the ISL95338 evaluation board and connect the EVB to the GUI interface.

Related Resources

ISL95338 Datasheet ISL95338 Datasheet

isl95338.pdf (1.76 MB)
Nov 2017

ISL95338EVAL1Z User Guide ISL95338EVAL1Z User Guide

isl95338eval1z-user-guide.pdf (1.75 MB)
Aug 2017

 


Video Transcript

Hi, my name is Phil Brinkley. I'm with Intersil, a Renesas company and today I want to demonstrate how to make use of the ISL95338 evaluation board.

First thing you do after you receive the board is to go to the landing page for the ISL95338 and download the GUI software that goes along with it as well the user's guide for the evaluation board.

The lab equipment you'll need to run the board is an adjustable DC power supply, a digital multimeter and an oscilloscope is nice to have but not essential.

Okay, once you unpack your board you want to make sure the jumpers are in the right place. This is J4 needs to be installed, J6 and seven need to be on the left side of that three pin header. The two switches S3 and S4 need to be to the left, being high. And switch one and switch two need to be to the right, being low.

Once you have your software installed you wanna plug in the USB. It should acknowledge with a beep that you've plugged it in and all three LEDs go on.

Forward Mode Operation

The first demo we're gonna walk through is forward mode in buck mode. So we're gonna apply power to the ADP side and measure the voltage out on the system side. Connect the multimeter up to your board to measure the output voltage on VSYS. As long as S1 is on the low side VSYS should read around zero volts. Once you have your board wired up go ahead and apply 12 volts to the board. Should check the current on the output. It should be very low, less than a milliamp or so. You'll notice that the two LEDs go out here, that implies that we have power to the board.

So you want to click on reset USB in the upper right-hand corner once the board is powered and the USB connected. And verify that you get a green checkmark on the USB interface. Once you have a green check mark you can read the manufacturer ID and you should see 0049 hex. That indicates that the board is connected and reading the registers properly.

So for forward mode in buck mode, we wanna set the output voltage to say five volts. You'll see that it rounds up to 5.004 volts. You want to write that register. You can also click on write all or read all. In this case, let's read all and verify that the D08 register, or that that value, was set in the register.

Once you have written the registers to drive approximately five volts out on VSYS you can measure that and switch S1 over to high. You should see around five volts. In our case we have it commanded to be 5.004 volts out and are reading very close to that. So we've now demonstrated forward mode using a buck converter; 12 volts in, five volts out. Let's now look at reverse mode. To do so we will reverse our connections and use the GUI to enable reverse mode operation.

Reverse Mode Operation

First, disable our power supply. Turn S1 back to low and we're gonna reverse our connections. So now I'm gonna put the power coming in on VSYS and we will measure the power out on the ADP side. Okay, now that we've reversed our connections we're gonna enable power coming into the VSYS. We have 12 volts coming in and around 0.2 milliamps being drawn. We're measuring the output. Currently, it's off. In the GUI I'm gonna set my reverse regulation voltage to five volts and write all the registers. I can read them to make sure that they did take and they did. And then I can enable switch two which will now turn on the output. We can see that the output measured now five volts. So we've demonstrated forward mode as well as reverse mode.

Buck to Buck-Boost to Boost Mode

Now that we've demonstrated both forward and reverse mode the other thing you can do is add an oscilloscope in. We can look at the phase voltages and watch how they change as our input voltage changes to move it from buck mode to buck-boost mode and to boost mode. So this is a look at the phase voltages. We currently have 12 volts coming in and five volts going out. So we're in buck mode. As I ramp down the power supply from 12 volts down to 7, 6, 5 now I can see it's moved into buck-boost mode and pure boost mode if I go down to 4 volts. As I go back up four, to five, to six, you can see that we're now back into buck mode. So that's 12 volts in and 5 volts out.

Well, thanks for watching and have a great day.