| |
|
| |
|
|
| Digitally Controlled Potentiometer (XDCP), Linear, 32 Taps, 3 Wire Interface, Terminal Voltages ± VCC |
| |
| |
|
|
|
|
| Buy Direct from Intersil |
 |
| | | | X9313ZS |  |
|
 |
| | | | X9313ZS |  |
|
 |
|
|
|
|
|
|
|
|
 | X9313 | | Digitally Controlled Potentiometer (XDCP), Linear, 32 Taps, 3 Wire Interface, Terminal Voltages ± VCC |
|  | | # of Devices/ Channels |  | 1 |  | | # of Taps |  | 32 |  | | Memory Type |  | Non-Volatile |  | | Bus Interface Type |  | 3-Wire (Up/Down) |  | | Resistance Options (kΩ) |  | 1, 10, 50 |  | | VCC Range (V) |  | 3.0 to 5.5 |  | | VCC (min) (V) |  | 3 |  | | VCC (max) (V) |  | 5.5 |  | | DCP Dual Supply Range (V) |  | N/A |  | | DCP Single Supply Range (V) |  | |  | | Resistance Taper |  | Linear |  | | Wiper Current (mA) |  | 4.4 |  | | Wiper Resistance (Ω) |  | 40 |  | | Supply Current (μA) |  | 200 |  | | Max Operating Temp (°C) |  | 85 |  | | End-to-End Tempco (ppm/°C) |  | 300 |  | | Middlepoint Ratiometric Tempco (ppm/°C) |  | 20 |  | | VL min. terminal voltage (V) |  | -5.5 |  | | VH max. terminal voltage (V) |  | 5.5 |  | | Features |  | Integrated charge pump to allow for single supply to swing -5.5V to 5.5V |  |
| |
| Key Features |
-
Solid-state potentiometer
-
3-wire serial interface
-
32 wiper tap points
-
Wiper position stored in nonvolatile memory and recalled on power-up
-
31 resistive elements
-
Temperature compensated
-
End to end resistance range ±20%
-
Terminal voltages, -VCC to +VCC
-
Low power CMOS
-
VCC = 3V or 5V
-
Active current, 3mA max.
-
Standby current, 500μA max.
-
High reliability
-
Endurance, 100,000 data changes per bit
-
Register data retention, 100 years
-
RTOTAL values = 1kΩ, 10kΩ, 50kΩ
-
Packages
-
8 Ld SOIC, 8 Ld MSOP and 8 Ld PDIP
-
Pb-free available (RoHS compliant)
|
|
| Description |
The Intersil X9313 is a digitally controlled potentiometer (XDCP). The device consists of a resistor array, wiper switches, a control section, and nonvolatile memory. The wiper position is controlled by a 3-wire interface. The potentiometer is implemented by a resistor array composed of 31 resistive elements and a wiper switching network. Between each element and at either end are tap points accessible to the wiper terminal. The position of the wiper element is controlled by the CS, U/D, and INC inputs. The position of the wiper can be stored in nonvolatile memory and then be recalled upon a subsequent power-up operation. The device can be used as a three-terminal potentiometer or as a two-terminal variable resistor in a wide variety of applications including: - Control
- Parameter adjustments
- Signal processing
|
|
iBuy direct from Intersil | iBuy direct - out of stock | Request samples | Check distributor inventory | Available in RoHS/Pb-Free | |  |
|
| Application Note(s): |
| | Datasheet(s): | | | Technical Brief(s): | | | Evaluation Board(s): | | | Technical Homepage: | | | |
|
|
|
| | ISL22511 | | Single Push Button Controlled Potentiometer (XDCP), Low Noise, Low Power, 32 Taps, PushButton Controlled Potentiometer | | | X9314 | | Single Digitally Controlled Potentiometer (XDCP) | | | X9315 | | Digitally Controlled Potentiometer (XDCP) | | | X93154 | | Digitally Controlled Potentiometer (XDCP) | | | X93155 | | Digitally Controlled Potentiometer (XDCP) | | | X93156 | | Single Digitally Controlled Potentiometer (XDCP), Low Noise, Low Power, 3 wire Up/Down, 32 Taps | | | X9511 | | Single Digitally-Controlled (XDCP) Potentiometer (Push Button Controlled) | |
|
|
|
|