Device Information
 
 
ISL88694 Printer Friendly Version
 
SMBus Accelerator (SMA)
 
Datasheets,
Related Docs
& Simulations
DescriptionKey
Features
Parametric
Data
Application
Diagrams
Related
Devices
 
 
Ordering Information
 iBuy direct from Intersil  iBuy direct - out of stock  Request samples
 Check distributor inventory Green/Pb(Lead free) Device  Available in RoHS/Pb-Free  
Part No. Design-In
Status
Temp. Package MSL Price
US $
PB Free
ISL88694EVAL Active   Eval Board N/A Contact Us  Buy Direct Disti-Buy  
ISL88694IH5Z Active Ind 5 Ld SOT-23 3 Contact Us PB Free Disti-Buy  
ISL88694IH5Z-TK Active Ind 5 Ld SOT-23 T+R 3 1.51 PB Free Buy Direct Disti-Buy Sample
ISL88694IH5 InActive Ind 5 Ld SOT-23 1 N/A      
ISL88694IH5-TK InActive Ind 5 Ld SOT-23 T+R 1 N/A      
The price listed is the manufacturer's suggested retail price for quantities of 1K units. However, prices in today's market are fluid and may change without notice.
MSL = Moisture Sensitivity Level - per IPC/JEDEC J-STD-020
SMD = Standard Microcircuit Drawing
 
  Description

The ISL88694 SMBus accelerator (SMA) is a dual active pull-up bus terminator designed to improve data transmission speed on SMBus or similar 2-wire serial bus interfaces. The ISL88694 is also compatible to the I2C serial bus.

The SMA detects rising input transitions with two internal voltage references and two comparators per channel. After the voltage on a data line crosses the first threshold (VTRIPL), the boost pull-up current source is activated to speed transition. After the voltage crosses the second threshold (VTRIPH), the boost pull-up current source is deactivated, leaving an active pull-up current of 275ľA on the line. When both channels are HIGH, the pull-up current for both lines is reduced to 100ľA to save power. Internal logic ensures that the active and boost pull-up current sources are not activated during downward transitions.

The level for VTRIPH is controlled by a bandgap voltage referred to VDD. This feature makes the switching behavior invariant for all power supply voltages between 2.7V and 5.5V.

A noise filter on each channel prevents the circuit from responding to input transitions that do not exceed a voltagetime threshold. To activate the boost circuit, the input must exceed VTRIPL by 100Vns (typical).

The SMA permits operation of the bus at frequencies up to 100kHz, despite the capacitive loads of multiple devices and/or long PC board traces. Enhanced ESD protection on the accelerator pins are guaranteed to withstand 8kV ESD (HBM) events.

The SMBus Accelerator provides an essential function in SMBus applications because of distributed capacitance of SMBus and multiple device input capacitances at various nodes. By incorporating SMA, systems using SMBus or I2C can reliably increase their bus load without the risk of data loss.

 
  Key Features
 
  • Active Termination for SMBus lines
  • Enhances System Bus Signal Rise Time
  • Increases Bus Capacity While Guaranteeing Data Integrity
  • 2.2mA Rise Time Supply Current
  • 8kV ESD Protection on SDA and SCL Pins
  • Wide Operating Voltage Range: 2.7V to 5.5V
  • 2-Wire SMBus and I2C Compatible (100kHz)
  • Small Package - SOT23-5
  • Pin-for-Pin Compatible with the LTC1694
  • Pb-Free Available (RoHS Compliant)
Related Documentation
 
Datasheet(s)   Datasheet(s):
 
Evaluation Board(s)   Evaluation Board(s):
 
Technical Homepage   Technical Homepage:
 
 
  Parametric Data
VTRIPL (V).75
VTRIPH (V)VDD-0.50
Standby Pull-Up Current (ľA)80
Active Pull-Up Current (ľA)275
Boost Pull-Up Current (mA)2.2
VS Range (V)2.7 to 5.5
 
  Application Block Diagrams
 
 
 
Applications
 
  • Servers
  • Data Acquisition
  • Routers
  • Battery Chargers
  • Portable Instrumentation
  • Notebook
  • PC
  • Facilities Tracking System

 

About Us | Careers | Contact Us | Investors | Legal | Privacy | Site Map | Subscribe | Intranet

©2003-2009. Intersil Americas Inc. All rights reserved.