Device Information
 
 
ICM7244 Printer Friendly Version
 
8-Character, Microprocessor-Compatible, LED Display Decoder Driver
 
Datasheets,
Related Docs
& Simulations
DescriptionKey
Features
Parametric
Data
Related
Devices
 
 
Ordering Information
 iBuy direct from Intersil  iBuy direct - out of stock  Request samples
 Check distributor inventory Green/Pb(Lead free) Device  Available in RoHS/Pb-Free  
Part No. Design-In
Status
Temp. Package MSL Price
US $
PB Free
ICM7244AIM44Z Active See Datasheet 44 Ld MQFP 3 7.48 PB Free Disti-Buy Sample
ICM7244AIM44ZT Active See Datasheet 44 Ld MQFP T+R 3 7.51 PB Free Disti-Buy  
The price listed is the manufacturer's suggested retail price for quantities of 1K units. However, prices in today's market are fluid and may change without notice.
MSL = Moisture Sensitivity Level - per IPC/JEDEC J-STD-020
SMD = Standard Microcircuit Drawing
 
  Description

The ICM7244 is an 8-character, alphanumeric display driver and controller which provides all the circuitry required to interface a microprocessor or digital system to a 16-segment display with internal pull-up resistors. It is primarily intended for use in microprocessor systems, where it minimizes hardware and software overhead. Incorporated on-chip are a 64-character ASClI decoder, 8x6 memory, high power character and segment drivers, and the multiplex scan circuitry.

6-bit ASCll data to be displayed is written into the memory directly from the microprocessor data bus. Data location depends upon the selection of either Sequential (MODE = 1) or Random access mode (MODE = 0). In the Sequential Access mode the first entry is stored in the lowest location and displayed in the "left-most" character position. Each subsequent entry is automatically stored in the next higher location and displayed to the immediate "right" of the previous entry. A DISPlay FULL signal is provided after 8 entries; this signal can be used for cascading devices together. A CLR pin is provided to clear the memory and reset the location counter. The Random Access mode allows the processor to select the memory address and display digit for each input word.

The character multiplex scan runs whenever data is not being entered. It scans the memory and CHARacter drivers, and ensures that the decoding from memory to display is done in the proper sequence. Intercharacter blanking is provided to avoid display ghosting.

 
  Key Features
 
  • 6-Segment Fonts with Decimal Point
  • Has Internal Pull-Up Resistors of 617Ω Typ.
  • Mask Programmable for Other Font-Sets Up to 64 Characters
  • Microprocessor Compatible
  • Directly Drives LED Common Cathode Displays
  • Cascadable Without Additional Hardware
  • Standby Feature Turns Display Off; Puts Chip in Low Power Mode
  • Sequential Entry or Random Entry of Data Into Display
  • Single +5V Operation
  • Character and Segment Drivers, All MUX Scan Circuitry, 8x6 Static Memory and 64-Character ASCll Font Generator Included On-Chip
  • Pb-Free (RoHS Compliant)
Related Documentation
 
Datasheet(s)   Datasheet(s):
 
Technical Homepage   Technical Homepage:
 
  Parametric Data
Alphanumeric?Y
# of Digits8 (16 segment)
Display TypeLED
Multiplexed?Y
FontASCII
InterfaceBIT PAR.,DIGIT SER.,RANDOM
Cycle Time (ns)250
 
  Related DevicesParametric Table   Parametric Table
 
 ICM7211A 4-Digit, LCD Display Driver 
 ICM7211AM 4-Digit, LCD Display Driver 
 ICM7218 8-Digit LED Microprocessor-Compatible Multiplexed Display Decoder Driver 
 ICM7228 8-Digit, Microprocessor-Compatible, LED Display Decoder Driver 
 ICM7243 8-Character, Microprocessor-Compatible, LED Display Decoder Driver 

 

About Us | Careers | Contact Us | Investors | Legal | Privacy | Site Map | Subscribe | Intranet

©2003-2009. Intersil Americas Inc. All rights reserved.