Device Information
 
 
HIP4083 Printer Friendly Version
 
80V/0.3A Peak Three Phase High Side Driver
 
Datasheets,
Related Docs
& Simulations
DescriptionKey
Features
Parametric
Data
Application
Diagrams
Related
Devices
 
 
Ordering Information
 iBuy direct from Intersil  iBuy direct - out of stock  Request samples
 Check distributor inventory Green/Pb(Lead free) Device  Available in RoHS/Pb-Free  
Part No. Design-In
Status
Temp. Package MSL Price
US $
PB Free
HIP4083ABT Active Automotive 16 Ld SOIC T+R 1 2.48   Disti-Buy  
HIP4083ABZ Active Automotive 16 Ld SOIC 3 2.07 PB Free Buy Direct Disti-Buy Sample
HIP4083ABZT Active Automotive 16 Ld SOIC T+R 3 2.07 PB Free Disti-Buy  
HIP4083APZ Active Automotive 16 Ld PDIP T+R N/A 2.07 PB Free Buy Direct Disti-Buy Sample
HIP4083EVAL Active   Eval Board N/A Contact Us   Disti-Buy  
HIP4083AB InActive Automotive 16 Ld SOIC 1 N/A      
HIP4083AP InActive Automotive 16 Ld PDIP N/A N/A      
The price listed is the manufacturer's suggested retail price for quantities of 1K units. However, prices in today's market are fluid and may change without notice.
MSL = Moisture Sensitivity Level - per IPC/JEDEC J-STD-020
SMD = Standard Microcircuit Drawing
 
  Description

The HIP4083 is a three phase high side N-channel MOSFET driver, specifically targeted for PWM motor control. Two HIP4083 may be used together for 3 phase full bridge applications (see application block diagram). Alternatively, the lower gates may be controlled directly from a buffered microprocessor output.

Unlike other members of the HIP408x family, the HIP4083 has no built in turn-on delay. Each output (AHO, BHO, and CHO) will turn-on 65ns after its input is switched low. Likewise, each output will turn-off 60ns after its input is switched high. Very short and very long dead times are possible when two HIP4083 are used to drive a full bridge. This dead time is controlled by the input signal timing.

The HIP4083 does not have a built in charge pump. Therefore, the bootstrap capacitors must be recharged on a periodic basis by initiating a short refresh pulse. In most bridge applications, this will happen automatically every time the lower FETs turn-on and the upper FETs turn-off. However, it is still possible to use the HIP4083 in applications that require the high side FETs to be on for extended periods of time. This can be easily accomplished by sending a short refresh pulse to the DIS pin.

The HIP4083 has reduced drive current compared to the HIP4086 making it ideal for low to moderate power applications. The HIP4083 is optimized for applications where size and cost are important. For high power applications driving large power FETs, the HIP4086 is recommended.

 
  Key Features
 
  • Independently Drives Three High Side N-Channel MOSFETs in Three Phase Bridge Configuration
  • Bootstrap Supply Max Voltage to 95VDC
  • Bias Supply Operation from 7V to 15V
  • Drives 1000pF Load with Typical Rise Times of 35ns and Fall Times of 30ns
  • CMOS/TTL Compatible Inputs
  • Programmable Undervoltage Protection
  • Pb-free Available
Related Documentation
 
Datasheet(s)   Datasheet(s):
 
Technical Brief(s)   Technical Brief(s):
 
 
  Parametric Data
Max Bootstrap Supply Voltage (V)95
Max Bias Voltage (V)15
Peak Pull-up Current (A)0.24 (avg)
Peak Pull-down Current (A)0.3 (avg)
Turn-On Prop Delay (ns)65
Turn-Off Prop Delay (ns)60
Rise Time (ns)35
Fall Time (ns)30
 
  Application Block Diagrams
 
 
 
Applications
 
  • Brushless Motors
  • High Side Switches
  • AC Motor Drives
  • Switched Reluctance Motor Drives
 
  Related DevicesParametric Table   Parametric Table
 
 HIP4080A 80V/2.5A Peak, High Frequency Full Bridge FET Driver with Charge Pump and Input Comparators 
 HIP4081A 80V/2.5A Peak, High Frequency Full Bridge FET Driver with Charge Pump and Independent Control Inputs 
 HIP4082 80V/1.25A Peak Current Full Bridge FET Driver 
 HIP4086 80V/0.5A Peak Three Phase Driver 
 ISL83202 55V, 1A Peak Current H-Bridge FET Driver 
 ISL83204A 60V/2.5A Peak, High Frequency Full Bridge FET Driver 

 

About Us | Careers | Contact Us | Investors | Legal | Privacy | Site Map | Subscribe | Intranet

©2003-2009. Intersil Americas Inc. All rights reserved.