New Products
All New Products
ISL29044A
April 2013
Low Power Ambient Light and Proximity Sensor with Internal IR-LED and Digital Output
The ISL29044A is an integrated ambient and infrared light-to-digital converter with a built-in IR LED and I2C Interface (SMBus Compatible). This device uses two independent ADCs for concurrently measuring ambient light and proximity in parallel. The flexible interrupt scheme is designed for minimal micro-controller utilization. More
ISL28022
April 2013
Precision Digital Power Monitor
The ISL28022 is a bi-directional high-side and low-side digital current sense and voltage monitor with serial interface. The device monitors current and voltage and provides the results digitally along with calculated power. The ISL28022 provides tight accuracy of less than 0.3% for both voltage and current monitoring over the entire input range. The digital power monitor has configurable fault thresholds and measurable ADC gain ranges. More
ISL95831C
April 2013
3+1 Voltage Regulator for IMVP-7/VR12™ CPUs
Compliant with IMVP-7/VR12™, the ISL95831C provides a complete solution for microprocessor and graphic processor core power supply. It provides two Voltage Regulators (VRs) with three integrated gate drivers. The first VR can be configured as 3-, 2- or 1-phase VR while the second output is 1-phase VR, providing maximum flexibility. The two VRs share the serial control bus to communicate with the CPU and achieve lower cost and smaller board area compared with the two-chip approach. More
HS-3530AEH
April 2013
Radiation Hardened Programmable Low Power Op Amps
The HS-3530ARH, HS-3530AEH are Low Power Operational Amplifiers, which are internally compensated monolithic devices offering a wide range of performance specifications. Parameters such as power dissipation, slew rate, bandwidth, noise and input DC parameters are programmed by selecting an external resistor or current source. Supply voltages as low as ±3V may be used with little degradation of AC performance. The HS-3530ARH, HS-3530AEH have been specifically designed to meet exposure to space radiation environments. Operation from -55°C to +125°C is guaranteed. More
HS-302EH
April 2013
Radiation Hardened CMOS Dual DPST Analog Switch
Intersil’s Satellite Applications Flow™ (SAF) devices are fully tested and guaranteed to 100kRAD Total Dose. These QML Class T devices are processed to a standard flow intended to meet the cost and shorter lead-time needs of large volume satellite manufacturers, while maintaining a high level of reliability. More
ISL1902
March 2013
Full-Featured, Dimmable AC Mains LED Driver with PFC
The ISL1902 is a high-performance, critical conduction mode (CrCM), single-ended controller used for More
TW2828
March 2013
HD/SD DVR Video Port Expander
TW2828 is a display and recording MUX chip with HD SPOT capability designed to work with popular H.264 CODEC on the market today. TW2828 provides a clean and cost effective MUX solution to the multi-channel PC HD DVR marketplace. On the embedded DVR market, using TW2828 in conjunction with a host SOC can deliver the most cost effective solution on the market. More
ISL98607
March 2013
High Efficiency Power Supply for Small Size Displays
The ISL98607 is a high efficiency power supply for small size displays, like smart phones, requiring ±supply rails. It integrates boost regulator, LDO, and inverting charge pump that are used to generate two output rails: +5V (default) and -5V (default). The ±5V output voltages can be adjusted up to ±5.7V with 50mV steps using the I2C interface. More
HS-303AEH
March 2013
Radiation Hardened CMOS Dual SPDT Analog Switch
The HS-303ARH, HS-303AEH, HS-303BRH, HS-303BEH analog switches are monolithic devices fabricated using Intersil’s dielectrically isolated Radiation Hardened Silicon Gate (RSG) process technology to insure latch-up free operation. They are pinout compatible and functionally equivalent to the HS-303RH, but offer improved 300kRAD(Si) total dose capability. These switches offers low-resistance switching performance for analog voltages up to the supply rails. “ON” resistance is low and stays reasonably constant over the full range of operating voltage and current. “ON” resistance also stays reasonably constant when exposed to radiation. Break-before-make switching is controlled by 5V digital inputs. The HS-303ARH should be operated with nominal ±15V supplies, while the HS-303BRH should be operated with nominal ±12V supplies. More
HS-303BEH
March 2013
Radiation Hardened CMOS Dual SPDT Analog Switch
The HS-303ARH, HS-303AEH, HS-303BRH, HS-303BEH analog switches are monolithic devices fabricated using Intersil’s dielectrically isolated Radiation Hardened Silicon Gate (RSG) process technology to insure latch-up free operation. They are pinout compatible and functionally equivalent to the HS-303RH, but offer improved 300kRAD(Si) total dose capability. These switches offers low-resistance switching performance for analog voltages up to the supply rails. “ON” resistance is low and stays reasonably constant over the full range of operating voltage and current. “ON” resistance also stays reasonably constant when exposed to radiation. Break-before-make switching is controlled by 5V digital inputs. The HS-303ARH should be operated with nominal ±15V supplies, while the HS-303BRH should be operated with nominal ±12V supplies. More
ISL24853A
March 2013
15-Channel I2C Programmable TFT-LCD Reference Voltage Generator with Dual-Bank, DVR VCOM, and Integrated EEPROM
The ISL24853A is a 15-channel I2C programmable reference voltage generator for TFT-LCDs featuring ultra-low power operation. It features 14 general purpose 10-bit DACs with buffered dual bank outputs, which can be used to set the column driver reference voltages of a TFT-LCD panel (gamma correction). The device also has an 8-bit current-sink DAC for VCOM calibration, and a high output current VCOM amplifier. The integrated EEPROM, for storing all reference voltage data, features an endurance of 10,000 write cycles and is read/write capable over the digital supply voltage range. More
HS-303CEH
March 2013
Radiation Hardened BiCMOS Dual SPDT Analog Switch
The HS-303CEH is an analog switch and a monolithic device that is fabricated using Intersil’s dielectrically isolated Radiation Hardened Silicon Gate (RSG) process technology to insure latch-up free operation. It is pinout compatible and functionally equivalent to the HS-303RH. This switch offers low-resistance switching performance for analog voltages up to the supply rails. ON-resistance is low and stays reasonably constant over the full range of operating voltage and current. ON-resistance also stays reasonably constant when exposed to radiation. Break-before-make switching is controlled by 5V digital inputs. The HS-303CEH can operate with rails of ±15V. More
ISL95818
March 2013
3-Phase PWM Controller for VR12.5 and VR12.6+ CPUs
Fully compliant with Intel VR12.5 and VR12.6+ specifications, the ISL95818 provides a complete solution for microprocessor core power supply. It provides a Voltage Regulator (VR) with two integrated and one external gate drivers. The VR can be configured as 3-, 2- or 1-phase, providing maximum flexibility. The VR uses the serial control bus to communicate with the CPU and achieves lower cost and smaller board area. More
ISL98604
March 2013
6-Channel Integrated LCD Supply
The ISL98604 is a high power, fully programmable More
TW2968
March 2013
8-Channel WD1 (960H)/D1 Compatible Video Decoders and Audio Codecs
The TW2968 is a low power NTSC/PAL video decoder chip that is designed for video surveillance applications. It consumes very low power in a typical composite input application. The available power down mode further reduces the power consumption. It uses the 1.0V for digital supply voltage and 3.3V for I/O and analog power. A single 27MHz crystal is all that needed to decode all analog video standards. More
TW2974
March 2013
4-CH WD1 (960H)/D1 Compatible Video Decoder and Audio Codec
The TW2974 is a low power NTSC/PAL video decoder chip that is designed for video surveillance applications. It consumes very low power in a typical composite input application. The available power down mode further reduces the power consumption. It uses the 1.0V for digital supply voltage and 3.3V for I/O and analog power. A single 27MHz crystal is all that needed to decode all analog video standards. More
HS-26CLV31EH
March 2013
Radiation Hardened 3.3V Quad Differential Line Drivers
The Intersil HS-26CLV31RH, HS-26CLV31EH are radiation hardened 3.3V quad differential line drivers designed for digital data transmission over balanced lines, in low voltage, RS-422 protocol applications. CMOS processing assures low power consumption, high speed, and reliable operation in the most severe radiation environments. More
HS-26C31EH
March 2013
Radiation Hardened Quad Differential Line Driver
The Intersil HS-26C31RH, HS-26C31EH are quad differential line drivers designed for digital data transmission over balanced lines and meets the requirements of EIA standard RS-422. Radiation hardened CMOS processing assures low power consumption, high speed, and reliable operation in the most severe radiation environments. More
ZL9010M
March 2013
Digital DC/DC PMBus 10A Power Module
The ZL9010M is a 10A variable output, step-down PMBus-compliant digital power supply. Included in the module is a high-performance digital PWM controller, power MOSFETs, an inductor, and all the passive components required for a highly integrated DC/DC power solution. This power module has More
ZL9006M
March 2013
Digital DC/DC PMBus 6A Power Module
The ZL9006M is a 6A variable output, step-down PMBus-compliant digital power supply. Included in the module is a high-performance digital PWM controller, power MOSFETs, an inductor, and all the passive components required for a highly integrated DC/DC power solution. This power module has built-in auto-compensation algorithms, which eliminates the need for manual compensation design work. The ZL9006M operates over a wide input voltage range and supports an output voltage range of 0.6V to 3.6V, which can be set by external resistors or via PMBus. Only bulk input and output capacitors are needed to finish the design. The output voltage can be precisely regulated to as low as 0.6V with ±1% output voltage regulation over line, load, and temperature variations. More
ISL95812
March 2013
Multiphase PWM Regulator for VR12.5, VR12.6 and VR12.6+ CPUs
Fully compliant with Intel VR12.5, VR12.6 and VR12.6+™ specifications, the ISL95812 provides a complete solution for microprocessor core power supply. It provides a Voltage Regulator (VR) with two integrated and one external gate drivers. The VR can be configured as 3-, 2- or 1-phase, providing maximum flexibility. The VR uses the serial control bus (SVID) to communicate with the CPU and achieves lower cost and smaller board area. More
ISL6208C
March 2013
High Voltage Synchronous Rectified Buck MOSFET Drivers
The ISL6208C is a high frequency, dual MOSFET driver, optimized to drive two N-Channel power MOSFETs in a synchronous-rectified buck converter topology. It is especially suited for mobile computing applications that require high efficiency and excellent thermal performance. The driver, combined with an Intersil multiphase Buck PWM controller, forms a complete single-stage core-voltage regulator solution for advanced mobile microprocessors. More
ISL9520
March 2013
Narrow VDC Regulator/Charger with SMBus Interface
The ISL9520 is a highly integrated Narrow VDC system voltage regulator and battery charger controller. Operating parameters are programmable over the System Management Bus (SMBus). The ISL9520 is designed for applications where the system power source is either the battery pack or the output of the regulator/charger. This makes the max voltage to the system equal to the max battery voltage instead of the max adapter voltage. The ISL9520 also includes a patented system to control trickle charging deeply discharged batteries while maintaining system voltage at a user defined minimum. High efficiency is achieved with a DC/DC More
TW5866
March 2013
9D1 H.264 CODEC with 8-Channel A/V Decoder
TW5866 is a H.264 CODEC solution with integrated8-channel analog A/V decoders. TW5866 supports up to 9D1 of H.264 video encoding, 8D1 of H.264 video decoding, or 4D1 H.264 full duplex codec. In addition, TW5866 supports motion JPEG encoding and video preview through BT.656 interfaces and PCI interfaces. TW5866 can be used in low cost H.264 hardware compression PCI card to support either 8-channel with a single chip, or 16-channel with two chips. It can also work with two external TW2866 to support 16-CIF H.264 compression. TW5866 can also be used in embedded DVR applications as an AV front-end chip working with display mux capable SOCs. More
ISL6730A
March 2013
Power Factor Correction Controllers
The ISL6730A, ISL6730B, ISL6730C, ISL6730D are active power factor correction (PFC) controller ICs that use a boost topology. (ISL6730B, ISL6730C, ISL6730D are Coming Soon.) The controllers are suitable for AC/DC power systems, up to 2kW and over the universal line input. More
ISL15110
March 2013
PLC MIMO Line Driver
The ISL15110 is a dual port differential line driver developed for Power Line Communication (PLC) Multi Input Multi Output (MIMO) applications. MIMO PLC requires transmission on one or two pairs of Phase, Neutral, and Ground wires. The device is designed to drive heavy line loads, while maintaining a high level of linearity required in OFDM PLC modem links. With 15.5dBm of total MIMO transmit signal power (12.5dBm per each pair) into a 50Ω line load, the drivers deliver -50dB average MTPR distortion across the output spectrum. More
ISL21090B75
February 2013
Ultra Low Noise, Precision Voltage Reference
The ISL21090 is a ultra low noise, high DC accuracy precision voltage reference with wide input voltage range. The ISL21090 uses the new Intersil Advanced Bipolar technology to achieve sub 1.0µVP-P (1.25V option) 0.1Hz to 10Hz noise with an initial voltage accuracy of 0.02% (2.5V option). More
HS-26CT32EH
February 2013
Radiation Hardened Quad Differential Line Receivers
"The Intersil HS-26CT32RH, HS-26CT32EH are differential line receivers designed for digital data transmission over balanced lines and meets the requirements of EIA standard RS-422. Radiation hardened CMOS processing assures low power consumption, high speed, and reliable operation in the most severe radiation environments. More
ISL95820
February 2013
Green Hybrid Digital Four Phase PWM Controller for Intel VR12.5™ CPUs
The ISL95820 Pulse Width Modulation (PWM) controller IC provides a complete low-cost solution for Intel VR12.5™ compliant microprocessor core power supplies. It provides the control and protection for a Voltage Regulator (VR). The VR incorporates 3 integrated drivers and can operate in 4-, 3-, 2- or 1-phase configurations. The VR uses a serial control bus to communicate with the CPU and achieve lower cost and smaller board area. More
ISL80019A
January 2013
Compact Synchronous Buck Regulators
ISL8002, ISL8002A, ISL80019 and ISL80019A are highly efficient, monolithic, synchronous step-down DC/DC converters that can deliver up to 2A of continuous output current from a 2.7V to 5.5V input supply. They use peak current mode control architecture to allow very low duty cycle operation. They operate at either 1MHz or 2MHz switching frequency, thereby providing superior transient response and allowing for the use of small inductors. They also have excellent stability and provide both internal and external compensation options. More
ISL8002
January 2013
Compact Synchronous Buck Regulators
ISL8002, ISL8002A, ISL80019 and ISL80019A are highly efficient, monolithic, synchronous step-down DC/DC converters that can deliver up to 2A of continuous output current from a 2.7V to 5.5V input supply. They use peak current mode control architecture to allow very low duty cycle operation. They operate at either 1MHz or 2MHz switching frequency, thereby providing superior transient response and allowing for the use of small inductors. They also have excellent stability and provide both internal and external compensation options. More
ISL8002A
January 2013
Compact Synchronous Buck Regulators
ISL8002, ISL8002A, ISL80019 and ISL80019A are highly efficient, monolithic, synchronous step-down DC/DC converters that can deliver up to 2A of continuous output current from a 2.7V to 5.5V input supply. They use peak current mode control architecture to allow very low duty cycle operation. They operate at either 1MHz or 2MHz switching frequency, thereby providing superior transient response and allowing for the use of small inductors. They also have excellent stability and provide both internal and external compensation options. More
ISL80019
January 2013
Compact Synchronous Buck Regulators
ISL8002, ISL8002A, ISL80019 and ISL80019A are highly efficient, monolithic, synchronous step-down DC/DC converters that can deliver up to 2A of continuous output current from a 2.7V to 5.5V input supply. They use peak current mode control architecture to allow very low duty cycle operation. They operate at either 1MHz or 2MHz switching frequency, thereby providing superior transient response and allowing for the use of small inductors. They also have excellent stability and provide both internal and external compensation options. More
ISL78223
January 2013
ZVS Full-Bridge PWM Controller with Adjustable Synchronous Rectifier Control
The ISL78223 is a high-performance zero-voltage switching (ZVS) full-bridge PWM controller. It achieves ZVS operation by driving the upper bridge FETs at a fixed 50% duty cycle while the lower bridge FETs are More
ISL6277A
December 2012
Multiphase PWM Regulator for AMD Fusion™ Mobile CPUs Using SVI 2.0
The ISL6277A is fully compliant with AMD Fusion™ SVI 2.0 and provides a complete solution for microprocessor and graphics processor core power. The ISL6277A controller supports two Voltage Regulators (VRs) with three integrated gate drivers and two optional external drivers for maximum flexibility. The Core VR can be configured for 3-, 2-, or 1-phase operation while the Northbridge VR supports 2- or 1-phase configurations. The two VRs share a serial control bus to communicate with the AMD CPU and achieve lower cost and smaller board area compared with two-chip solutions. More
ISL59960
December 2012
960MegaQ™: An Automatic 960H and Composite Video Equalizer, Fully-Adaptive to 4000 Feet
The ISL59960 is a single-channel adaptive equalizer for 960H (WD1) or 720H (D1) composite video designed to automatically compensate for long runs of CAT 5/CAT 6 or RG-59 cable, producing high quality video output with no user interaction. The ISL59960 equalizes up to 4000 feet (1200 meters) of CAT 5/CAT 6 cable. More
ISL94212
December 2012
Multi-Cell Li-Ion Battery Manager
The ISL94212 is a Multi-cell Li-ion battery manager IC that supervises up to 12 series connected cells. The part performs accurate monitoring, cell balancing and extensive system diagnostics functions. Three cell balancing modes are provided: manual mode, timed mode and an auto-balance mode which terminates balancing functions when a (host microcontroller specified) charge transfer value has been met. More
ISL37231
December 2012
10.3125 Gb/s Retiming Dual-Channel Transceiver
The ISL37231 is an advanced dual-channel, dual-simplex retimer for active copper cable applications. Endowed with sophisticated functions, such as media optimized (PCB or Cable) and adaptive equalization, de-emphasis, and signal retiming, this IC fortifies sensitive links that break with lesser retiming solutions. The device contains high performance mixed signal processing technology to provide a maximally robust signal integrity solution for datacenter and consumer applications. Such processing includes up to 25dB of media-optimized equalization and versatile retiming capabilities to reset link jitter budgets. More
ISL95873
December 2012
Buck PWM Controller with Internal Compensation and External Reference Tracking
The ISL95873 is a Single-Phase Synchronous-Buck PWM controller featuring Intersil’s proprietary R4™ Technology. The R4™ modulator has integrated compensation, fast transient performance, accurate switching frequency control, and excellent light-load efficiency. These technology advances, together with integrated MOSFET drivers and a Schottky bootstrap diode, allow for a high performance regulator that is highly compact and needs few external components. Differential remote sensing of the output voltage is an additional feature. For maximum efficiency, the converter automatically enters diode-emulation mode (DEM) during light-load conditions, such as system standby. More
ISL78419
December 2012
Integrated Automotive TFT-LCD Power Supply Regulator
The ISL78419 is an integrated power management IC (PMIC) for TFT-LCDs used in central display, rear seat entertainment and virtual dashboards. The device integrates a boost converter for generating AVDD, an LDO regulator for VLOGIC. VON and VOFF are generated by a charge pump driven by the switch node of the boost converter. The ISL78419 also includes a VON slice circuit, reset function, and a high performance VCOM amplifier with a Digitally Controlled Potentiometer (DCP) that is used as a VCOM calibrator. More
HS-26CLV32EH
December 2012
Radiation Hardened 3.3V Quad Differential Line Receiver
The Intersil HS-26CLV32RH is a radiation hardened 3.3V quad differential line receiver designed for digital data transmission over balanced lines, in low voltage, RS-422 protocol applications. Radiation hardened CMOS processing assures low power consumption, high speed, and reliable operation in the most severe radiation environments. More
ISL94203
December 2012
3-to-8 Cell Li-ion Battery Pack Monitor
The ISL94203 is a Li-ion battery monitor IC that supports from 3 to 8 series connected cells. It provides full battery monitoring and pack control. The ISL94203 provides automatic shutdown and recovery from out of bounds conditions and automatically controls pack cell balancing. More
TW2964
December 2012
4-CH WD1 (960H)/D1 Compatible Video Decoders and Audio Codecs
The TW2964 is a low power NTSC/PAL video decoder chip that is designed for video surveillance applications. It consumes very low power in a typical composite input application. The available power down mode further reduces the power consumption. It uses the 1.0V for digital supply voltage and 3.3V for I/O and analog power. A single 27MHz crystal is all that needed to decode all analog video standards. More
ISL94208
December 2012
4- to 6-Cell Li-ion Battery Management Analog Front-End
The ISL94208 battery management IC is designed for use with a microcontroller and features an analog More
ISL21090B50
December 2012
Ultra Low Noise, Precision Voltage Reference
The ISL21090 is a ultra low noise, high DC accuracy precision voltage reference with wide input voltage range. The ISL21090 uses the new Intersil Advanced Bipolar technology to achieve sub 1.0µVP-P (1.25V option) 0.1Hz to 10Hz noise with an initial voltage accuracy of 0.02% (2.5V option). More
ISL8225M
November 2012
Dual 15A/Single 30A Step-Down Power Module
The ISL8225M is a fully-encapsulated step-down switching power supply that can deliver up to 100W output power from a small 17mm square PCB footprint. The two 15A outputs may be used independently or combined to deliver a single 30A output. Designing a high-performance board-mounted power supply has never been simpler -- only a few external components are needed to create a very dense and reliable power solution. More
ISL6446A
November 2012
Dual (180° Out-of-Phase) PWM and Linear Controller
The ISL6446A is a high-performance, triple output controller that provides a single high-frequency power solution primarily for Broadband, DSL and Networking applications. This device integrates complete control, monitoring and protection functions for two synchronous buck PWM controllers and one linear controller. Input voltage ripple and total RMS input current is substantially reduced by synchronized 180° out-of-phase operation of the two PWMs. More
EL5120T
November 2012
12MHz Rail-to-Rail Input-Output Operational Amplifier
The EL5120T is a high voltage rail-to-rail input-output amplifier with low power consumption. The EL5120T is a single amplifier that exhibits beyond the rail input capability, rail-to-rail output capability, and is unity gain stable. More
ISL29044
November 2012
Low Power Ambient Light and Proximity Sensor with Internal IR-LED and Digital Output
The ISL29044 is an integrated ambient and infrared light-to-digital converter with a built-in IR LED and I2C Interface (SMBus Compatible). This device uses two independent ADCs for concurrently measuring ambient light and proximity in parallel. The flexible interrupt scheme is designed for minimal microcontroller utilization. More
ISL26104
October 2012
Low-Noise 24-bit Delta Sigma ADC
The ISL26102 and ISL26104 provide a low-noise programmable gain amplifier along with a 24-bit Delta-Sigma Analog-to-Digital Converter with two channel (ISL26102) or four channel (ISL26104) differential, multiplexed inputs. The devices feature exceptional noise performance for conversion rates ranging from 2.5Sps to 4kSps. More
ISL26102
October 2012
Low-Noise 24-bit Delta Sigma ADC
The ISL26102 and ISL26104 provide a low-noise programmable gain amplifier along with a 24-bit Delta-Sigma Analog-to-Digital Converter with two channel (ISL26102) or four channel (ISL26104) differential, multiplexed inputs. The devices feature exceptional noise performance for conversion rates ranging from 2.5Sps to 4kSps. More
HS-1825AEH
October 2012
Radiation Hardened High-Speed, Dual Output PWM
The Radiation Hardened HS-1825ARH, HS-1825AEH Pulse Width Modulator is designed to be used in high frequency switched-mode power supplies and can be used in either current-mode or voltage-mode. It is well suited for single-ended boost converter applications. More
HS-139EH
October 2012
Radiation Hardened Quad Voltage Comparator
"The Radiation Hardened HS-139RH, HS-139EH consists of four independent single or dual supply voltage comparators on a single monolithic substrate. The common mode input voltage range includes ground, even when operated from a single supply and the low supply current makes these comparators suitable for low power applications. These types were designed to directly interface with TTL and CMOS. More
ZL8101
October 2012
Adaptive Digital DC/DC PWM Controller with Auto Compensation
The ZL8101 is a digital PWM controller with auto compensation that is designed to work with either the ZL1505 MOSFET driver IC, ISL6611 Phase Doubler IC, or DrMOS type devices. Current sharing allows multiple devices to be connected in parallel to source loads with very high current demands. Adaptive performance optimization algorithms improve power conversion efficiency across the entire load range. Zilker Labs Digital-DC™ technology enables a blend of power conversion performance and power management features. More
ISL29038
October 2012
Low Power Ambient Light and Proximity Sensor with Enhanced Infrared Rejection
The ISL29038 is a low power Ambient Light Sensor (ALS) and proximity (PROX) sensor. It has a built-in IR-LED driver for proximity function. The ALS function measures the amount of light (in the visible spectrum) incident on the ISL29038. More
ISL6625A
September 2012
Synchronous Rectified Buck MOSFET Drivers
The ISL6625A is a high frequency MOSFET driver designed to drive upper and lower power N-Channel MOSFETs in a synchronous rectified buck converter topology. More
ISL88736
September 2012
SMBus Level 2 Battery Charger with Boost Mode
The ISL88736 is a highly integrated Lithium-ion battery charger controller, programmable over the SMBus system management bus (SMBus). The ISL88736 is intended to be used in a smart battery charger (SBC) within a smart battery system (SBS) that throttles the charge power, such that the current from the AC-adapter is automatically limited. High efficiency is achieved with a DC/DC synchronous-rectifier buck converter, equipped with diode emulation for enhanced light load efficiency. The ISL88736 charges one to four Lithium-ion series cells, and delivers up to 8A charge current. Integrated MOSFET drivers and bootstrap diode result in fewer components and smaller implementation area. Low offset current-sense amplifiers provide high accuracy with 10mΩ sense resistors. The ISL88736 provides 0.5% end-of-charge battery voltage accuracy. More
ISL88732
September 2012
SMBus Level 2 Battery Charger with Boost Mode
The ISL88732 is a highly integrated Lithium-ion battery charger controller, programmable over the SMBus system management bus (SMBus). The ISL88732 is intended to be used in a smart battery charger (SBC) within a smart battery system (SBS) that throttles the charge power such that the current from the AC-adapter is automatically limited. High efficiency is achieved with a DC/DC synchronous-rectifier buck converter, equipped with diode emulation for enhanced light load efficiency. The ISL88732 charges one to four Lithium-ion series cells, and delivers up to 8A charge current. Integrated MOSFET drivers and bootstrap diode result in fewer components and smaller implementation area. Low offset current-sense amplifiers provide high accuracy with 10mΩ sense resistors. The ISL88732 provides 0.5% end-of-charge battery voltage accuracy. More
ISL88733
September 2012
SMBus Level 2 Battery Charger
The ISL88733 is a highly integrated Lithium-ion battery charger controller, programmable over the SMBus system management bus (SMBus). The ISL88733 is intended to be used in a smart battery charger (SBC) within a smart battery system (SBS) that throttles the charge power such that the current from the AC-adapter is automatically limited. High efficiency is achieved with a DC/DC synchronous-rectifier buck converter, equipped with diode emulation for enhanced light load efficiency. The ISL88733 charges one to four Lithium-ion series cells, and delivers up to 8A charge current. Integrated MOSFET drivers and bootstrap diode result in fewer components and smaller implementation area. Low offset current-sense amplifiers provide high accuracy with 10mΩ sense resistors. The ISL88733 provides 0.5% end-of-charge battery voltage accuracy. More
ISL76123
September 2012
Automotive Single Supply, SPDT Analog Switch
The Intersil ISL76123 device is a small precision, bidirectional, single-pole/double throw (SPDT) analog switch, designed to operate from a single +2.7V to +12V supply. The device is supplied in a 6 Ld SOT-23 package. Targeted applications include automotive battery powered systems that can benefit from the device’s low power consumption (5µW), low leakage currents (3nA max), and fast switching speeds (tON = 28ns, tOFF = 20ns). This device will often find use in infotainment systems to “mux - in” additional functions to GPIO pins on SOCs. The device ensures the switching function is always break-before-make to help eliminate transient signal problems. Its small package size alleviates board space limitations. The part has been qualified for use in automotive applications over an operating temperature range of -40°C to +105°C. More
ISL78420
September 2012
100V, 2A Peak, Half-Bridge Driver with Tri-Level PWM Input and Adjustable Dead-Time
The ISL78420 is a 100V, high frequency, half-bridge MOSFET driver with a tri-level PWM input. This part is a derivative of the HIP2121 half-bridge driver. The non-automotive version of the ISL78420 is the HIP2124. More
ISL78840ASEH
September 2012
Radiation Hardened, High Performance Industry Standard
Single-Ended Current Mode PWM Controller
The ISL7884xASEH is a high performance, radiation hardened drop-in replacement for the popular 28C4x and 18C4x PWM controllers suitable for a wide range of power conversion applications including boost, flyback, and isolated output configurations. Its fast signal propagation and output switching characteristics make this an ideal product for existing and new designs. More
ISL78841ASEH
September 2012
Radiation Hardened, High Performance Industry Standard
Single-Ended Current Mode PWM Controller
The ISL7884xASEH is a high performance, radiation hardened drop-in replacement for the popular 28C4x and 18C4x PWM controllers suitable for a wide range of power conversion applications including boost, flyback, and isolated output configurations. Its fast signal propagation and output switching characteristics make this an ideal product for existing and new designs. More
ISL78843ASEH
September 2012
Radiation Hardened, High Performance Industry Standard
Single-Ended Current Mode PWM Controller
The ISL7884xASEH is a high performance, radiation hardened drop-in replacement for the popular 28C4x and 18C4x PWM controllers suitable for a wide range of power conversion applications including boost, flyback, and isolated output configurations. Its fast signal propagation and output switching characteristics make this an ideal product for existing and new designs. More
ISL78845ASEH
September 2012
Radiation Hardened, High Performance Industry Standard
Single-Ended Current Mode PWM Controller
The ISL7884xASEH is a high performance, radiation hardened drop-in replacement for the popular 28C4x and 18C4x PWM controllers suitable for a wide range of power conversion applications including boost, flyback, and isolated output configurations. Its fast signal propagation and output switching characteristics make this an ideal product for existing and new designs. More
ISL8200AM
September 2012
Complete Current Share 10A DC/DC Power Module
The ISL8200AM is a simple and easy to use high power, current-sharing DC/DC power module for Datacom/Telecom/FPGA power hungry applications. All that is needed is the ISL8200AM, a few passive components and one VOUT setting resistor to have a complete 10A design ready for market. More
ISL97900
September 2012
RGB Buck-Boost 3-Channel Color Sequencing LED Driver
The ISL97900 is a highly efficient 3-channel, 1.5A sequential LED driver powered from a single-cell Li-ion battery, or regulated input voltage up to 5.5V. This LED driver incorporates an independent current controlled driving mechanism for each of the LED's, which allows accurate current control of the LED brightness. More
ISL6367H
September 2012
Green Hybrid Digital Dual 6-Phase + 1-Phase PWM Controller for R12.5/VR12/IMVP7 Applications With SMBus/PMBus/I2C
The ISL6367H is a Hybrid Digital dual PWM controller and is designed to be compliant to Intel VR12.5/VR12/IMVP7 specifications. Its 6-phase PWMs control the microprocessor core or memory voltage regulator, while its single-phase PWM controls the peripheral voltage regulator for graphics, system agent, or processor I/O. It includes programmable functions and telemetries for easy use, high system flexibility and overclocking applications using SMBus, PMBus, or I2C interface, which is designed to be conflict free with CPU’s SVID bus. This hybrid digital approach eliminates the need for NVM and Firmware often seen in a full digital solution and significantly reduces design complexity, inventory and manufacturing costs. More
ISL70417SEH
September 2012
Rad Hard 40V Quad Precision Low Power Operational Amplifiers
The ISL70417SEH contains four very high precision amplifiers featuring the perfect combination of low noise vs power consumption. Low offset voltage, low IBIAS current and low temperature drift making them the ideal choice for applications requiring both high DC accuracy and AC performance. The combination of high precision, low noise, low power and small footprint provides the user with outstanding value and flexibility relative to similar competitive parts. More
IS-2100AEH
September 2012
Radiation Hardened High Frequency Half Bridge Drivers
The Radiation Hardened IS-2100ARH, IS-2100AEH are high frequency, 130V Half Bridge N-Channel MOSFET Driver ICs, which are functionally similar to industry standard 2110 types. The low-side and high-side gate drivers are independently controlled. This gives the user maximum flexibility in dead-time selection and driver protocol. More
ISL75051SEH
September 2012
3A, Rad Hard, Positive, Ultra Low Dropout Regulator
The ISL75051SEH is a radiation hardened low-voltage, high-current, single-output LDO specified for up to 3.0A of continuous output current. These devices operate over an input voltage range of 2.2V to 6.0V and are capable of providing output voltages of 0.8V to 5.0V adjustable based on resistor divider setting. Dropout voltages as low as 65mV can be realized using the device. More
IS-139ASEH
August 2012
Single Event Radiation Hardened Quad Voltage Comparators
The single event effects and total dose radiation hardened IS-139ASRH, IS-139ASEH consist of four independent single or dual supply voltage comparators on a single monolithic substrate. The common mode input voltage range includes ground, even when operated from a single supply, and the low supply current makes these comparators suitable for low power applications. These types were designed to directly interface with TTL and CMOS inputs. More
ISL24863A
August 2012
15-Channel I2C Programmable TFT-LCD Reference Voltage Generator with Dual-Bank, DVR VCOM, Integrated EEPROM, and Ultra-low Power Operation
The ISL24863A is a 15-channel I2C programmable reference voltage generator for TFT-LCDs featuring ultra-low power operation. It features 14 general purpose 10-bit DACs with buffered dual bank outputs, which can be used to set the column driver reference voltages of a TFT-LCD panel (gamma correction). The device also has an 8-bit current-sink DAC for VCOM calibration, and a high output current VCOM amplifier. The integrated EEPROM, for storing all reference voltage data, features an endurance of 10,000 write cycles and is read/write capable over the digital supply voltage range. More
TW2851
August 2012
Advanced 4-Channel A/V Decoder, MUX and Display Processor
The TW2851 is Techwells 5th generation 4-channel A/V decoder, multiplexer and display processor IC for security surveillance applications. The device has four built-in NTSC/PAL video decoders with high-performance adaptive 4H comb filters, noise reduction algorithm, independent and flexible video scalars for the display and record paths and 16x12 matrix motion/blind/night detectors. The device includes advanced record and display multiplexer functions. The record multiplexer supports multichannel frame-, field- and byte-interleaved video streams with a total frame rate of up to 120 frames per second. The channel ID and motion/blind/night detection information can be embedded in the video stream for record and playback purposes. The display multiplexer supports up to eight video windows of which the location and size of each window is configurable. The multiplexed output can be displayed via VGA/LVDS and CVBS interfaces. Also included is a SPOT multiplexer that can tile multiple live camera images and/or live record images on an analog output for displaying on SPOT monitor or time multiplex multiple camera images on a digital output for network function. The TW2851 has an audio CODEC which has four audio ADCs and one DAC. A built-in audio controller can generate digital outputs for recording/mixing and accept digital input for playback. Multiple TW2851 devices can be cascaded to support 8/12/16-channel applications. Up to 32 display windows can be displayed on the PC monitor or LCD panel. Other key features of the TW2851 includes 16-bit bitmap OSG, 2D-deinterlacer, 8- channel nonreal time switching inputs, and flexible record and playback ports supporting BT.656, BT.601, BT.1120 and 24-bit RGB formats. More
ISL70218SEH
August 2012
Rad Hard Dual 36V Precision Single-Supply, Rail-to-Rail Output, Low-Power Operational Amplifiers
The ISL70218SEH is a dual, low-power precision amplifier optimized for single-supply applications. This op amp features a common mode input voltage range extending to 0.5V below the V- rail, a rail-rail differential input voltage range, and rail-to-rail output voltage swing, which makes it ideal for single-supply applications where input operation at ground is important. More
ISL70227SEH
August 2012
36V Rad Hard Dual Precision Operational Amplifier
The ISL70227SEH is a high precision dual operational amplifier featuring very low noise, low offset voltage, low input bias current and low temperature drift. These features plus its radiation tolerance make the ISL70227SEH the ideal choice for applications requiring both high DC accuracy and AC performance. The combination of precision, low noise, and small footprint provides the user with outstanding value and flexibility relative to similar competitive parts. More
ISL267450
August 2012
12-Bit, 1MSPS SAR ADCs
The ISL267450 is a 12-bit, 1MSPS sampling SAR-type ADC with a differential input span of 2*VREF volts. The ISL267450 features excellent linearity over supply and temperature variations and is drop-in compatible with the AD7450. The device can operate from a supply voltage of either 5V or 3V and maintain measurement accuracy with input signals up to the supply rails. More
ISL6377
August 2012
AMD Fusion™ Desktop CPUs Using SVI 2.0
The ISL6377 is fully compliant with AMD Fusion™ SVI 2.0 and provides a complete solution for microprocessor and graphics processor core power. The ISL6377 controller supports two Voltage Regulators (VRs) with three integrated gate drivers and three optional external drivers for maximum flexibility. The Core VR can be configured for 4-, 3-, 2-, or 1-phase operation while the Northbridge VR supports 2- or 1-phase configurations. The two VRs share a serial control bus to communicate with the AMD CPU and achieve lower cost and smaller board area compared with two-chip solutions. More
ISL1903
August 2012
Dimmable Buck LED Driver - AC Mains or DC Input LED Driver
The ISL1903 is a high-performance, critical conduction mode (CrCM), single-ended buck LED driver controller. It may be used with DC input converters, but also supports single-stage conversion of the AC mains to a constant current source with power factor correction (PFC). The ISL1903 supports buck converter topologies, such as isolated forward converters or non-isolated source return buck converters. Operation in CrCM allows near zero-voltage switching (ZVS) for improved efficiency while maximizing magnetic core utilization. More
ISL1904
August 2012
Dimmable AC Mains LED Driver with PFC and Primary Side Regulation
The ISL1904 is a high-performance, critical conduction mode (CrCM), flyback controller used for single-stage conversion of the AC mains to a constant current source with power factor correction (PFC). The controller regulates the output current by monitoring the primary side switching current so the feedback signal does not cross the isolation barrier. Operation in CrCM allows near zero-voltage quasi-resonant switching (ZVS) for improved efficiency while maximizing magnetic core utilization. The ISL1904 LED driver provides all of the features required for high-performance dimmable LED ballast designs and supports AC or DC input, isolated or non-isolated flyback and boost topologies. This advanced BiCMOS controller features all of the functions required to design low cost low parts count LED driver. More
ISL24111
August 2012
9-Channel High Voltage TFT-LCD Logic Level Shifter with Gate Shaping Function
The ISL24111 is a nine output channel high voltage TFT-LCD logic level shifter. The ISL24111 converts low power logic-level input timing signals, generated by the TFT-LCD timing controller (TCON), to high power level-shifted output signals used to drive a Gate-In-Panel (GIP) TFT-LCD. The high voltage level shifters can swing up to +60V, with peak output current of +460mA (source) and -730mA (sink). More
ISL6446
August 2012
Dual (180° Out-of-Phase) PWM and Linear Controller
The ISL6446 is a high-performance, triple output controller that provides a single high-frequency power solution primarily for Broadband, DSL and Networking applications. This device integrates complete control, monitoring and protection functions for two synchronous buck PWM controllers and one linear controller. Input voltage ripple and total RMS input current is substantially reduced by synchronized 180° out-of-phase operation of the two PWMs. More
ISL97692
August 2012
Single or Multiple Cell Li-ion Battery Powered 4-Channel and 6-Channel LED Drivers
The ISL97692, ISL97693, ISL97694A are Intersil’s highly integrated 4- and 6-channel LED drivers for display backlighting . These parts maximize battery life by featuring only 1mA quiescent current, and by operating down to 2.4V input voltage, with no need for higher voltage supplies. More
ISL24867
August 2012
15-Channel I2C Programmable TFT-LCD Reference Voltage Generator with Dual-Bank, DVR VCOM, GND Outputs, EEPROM, and Ultra-low Power Operation
The ISL24867 is a programmable reference voltage generator for TFT-LCDs featuring ultra-low power operation. The ISL24867 contains an I2C programmable, 10-bit, 14-channel gamma reference voltage generator with buffered dual bank outputs, an 8-bit programmable DVR VCOM calibrator, high output current VCOM amplifier, and a GND outputs function with logic (EN) control. The integrated EEPROM, for storing all reference voltage data, features an endurance of 10,000 write cycles and is read/write capable over the digital supply voltage range. The dual bank outputs are capable of fast switching between different sets of voltage reference data. Bank switching is ideal to quickly change between gamma curves for 2D/3D TFT-LCD applications. The device's outputs are double buffered, which allows for updating data in one bank while data is simultaneously output from the other bank. Combining gamma and VCOM reference voltage generators, with low power operation, and EEPROM, the ISL24867 provides a complete reference voltage solution ideal for tablet, monitor, and mobile TFT-LCD applications. The ISL24867 is available in a Super Thin 28 Ld 4x5mm X2QFN thermally enhanced package. It is specified for operation over the -40°C to +85°C ambient temperature range. More
ISL26321
August 2012
12-bit, 250kSPS Low-power ADC with Single-ended and Differential Inputs and Multiple Input Channels
The ISL26320/21/22/23/24/25/29 family of sampling SAR-type ADCs feature excellent linearity over supply and temperature variations, and offer versions with 1-, 2-, 4- and 8-channel single-ended inputs, and 1-, 2- and 4-channel differential inputs. More
ISL26311
August 2012
12-bit, 125kSPS Low-power ADCs with Single-ended and Differential Inputs and Multiple Input Channels
The ISL26310/11/12/13/14/15/19 family of sampling SAR-type ADCs feature excellent linearity over supply and temperature variations, and offer versions with 1-, 2-, 4- and 8-channel single-ended inputs, and 1-, 2- and 4-channel differential inputs. More
ISL97694A
August 2012
Single or Multiple Cell Li-ion Battery Powered 4-Channel and
6-Channel LED Drivers
The ISL97692, ISL97693, ISL97694A are Intersil’s highly integrated 4- and 6-channel LED drivers for display backlighting . These parts maximize battery life by featuring only 1mA quiescent current, and by operating down to 2.4V input voltage, with no need for higher voltage supplies. More
ISL28915
August 2012
Nano Power, Push/Pull Output Comparator
The ISL28915 is a nano power comparator optimized for low-power applications. This device is designed for single-supply operation from 1.8V to 5.5V and typically consumes 500nA of supply current. These devices also feature a push/pull output stage with rail-to-rail input and output swing (RRIO), allowing for maximum battery usage. More
ISL267452
July 2012
12-Bit, 555kSPS SAR ADC
The ISL267452 is a 12-bit, 555kSPS sampling SAR-type ADC featuring excellent linearity over supply and temperature variations, and is drop-in compatible with the AD7452. The robust, fully-differential input offers high impedance to minimize errors due to leakage currents, and the specified measurement accuracy is maintained with input signals up to the supply rails. More
ISL9113
July 2012
Low Input Voltage and High Efficiency Synchronous Boost Converter with 1.3A Switch
The ISL9113 provides a power supply solution for devices powered by three-cell alkaline, NiCd, NiMH, or More
D2-92683
July 2012
Intelligent Digital Amplifier and Sound Processor
The D2-926xx family of the DAE-3™ and DAE-3HT™ Digital Audio Engine™ devices are complete System-on Chip (SoC) multi-channel digital sound processors and Class-D amplifier controllers. More
D2-92684
July 2012
Intelligent Digital Amplifier and Sound Processor
The D2-926xx family of the DAE-3™ and DAE-3HT™ Digital Audio Engine™ devices are complete System-on Chip (SoC) multi-channel digital sound processors and Class-D amplifier controllers. More
HS-1840BEH
July 2012
Rad-Hard 16 Channel BiCMOS Analog Multiplexer with High-Z Analog Input Protection
The HS-1840ARH, HS-1840AEH, HS-1840BRH and HS-1840BEH are radiation hardened, monolithic 16 channel multiplexers constructed with the Intersil Rad-Hard Silicon Gate, bonded wafer, Dielectric Isolation process. They are designed to provide a high input impedance to the analog source if device power fails (open), or the analog signal voltage inadvertently exceeds the supply by up to ±35V, regardless of whether the device is powered on or off. Excellent for use in redundant applications, since the secondary device can be operated in a standby unpowered mode affording no additional power drain. More significantly, a very high impedance exists between the active and inactive devices preventing any interaction. One of sixteen channel selections is controlled by a 4-bit binary address plus an Enable-Inhibit input which conveniently controls the ON/OFF operation of several multiplexers in a system. All inputs have electrostatic discharge protection. The More
IS-1845ASEH
July 2012
Single Event Radiation Hardened High Speed, Current Mode PWM
The IS-1845ASRH, IS-1845ASEH are designed to be used in switching power supplies operating in current mode. The rising edge of the on-chip oscillator turns on the output. Turn-off is controlled by the current sense comparator and occurs when the sensed current reaches a peak controlled by the error amplifier. More
ISL1801
July 2012
sPMIC for Micro-Converter Bias and Drivers
The ISL1801 is a power management IC (PMIC) optimized for solar array micro-converters and other systems operating from a high voltage DC supply. The ISL1801 can be used in buck, boost or buck-boost micro-converter topologies in order to maximize the energy harvest from a solar array. In addition to the power stage and main controller, the ISL1801 includes the bias regulators, gate drivers, current sense amplifier and comparators needed for micro-converters. More
ISL26320
July 2012
12-bit, 250kSPS Low-power ADCs with Single-endedand Differential Inputs and Multiple Input Channels
The ISL26320/21/22/23/24/25/29 family of sampling SAR-type ADCs feature excellent linearity over supply and temperature variations, and offer versions with 1-, 2-, 4- and 8-channel single-ended inputs, and 1-, 2- and 4-channel differential inputs. More
ISL26323
July 2012
12-bit, 250kSPS Low-power ADCs with Single-endedand Differential Inputs and Multiple Input Channels
The ISL26320/21/22/23/24/25/29 family of sampling SAR-type ADCs feature excellent linearity over supply and temperature variations, and offer versions with 1-, 2-, 4- and 8-channel single-ended inputs, and 1-, 2- and 4-channel differential inputs. More
ISL97901
June 2012
RGB Buck-Boost Four-Channel LED Driver with Color Sequencing and Automatic White Balance
The ISL97901 is a highly efficient four channel, 1.5A sequential LED driver powered from a single-cell Li-ion battery, or regulated input voltage up to 5.5V. The ISL97901 incorporates an independent current controlled driving mechanism for each of the LED's to allow accurate brightness control. More
ISL58303
June 2012
800mA Triple Output Laser Diode Driver
The ISL58303, ISL58304 are high-speed triple output laser diode drivers designed to support color field sequential laser light source Pico projection modules. Output channels are designed with independent programmable bias and threshold adjustment to support a wide range of laser diode manufacturers. Both laser diode drivers offer exceptional power efficiency and a high degree of system integration allowing a compact and cost effective system design. More
ISLA214P12
June 2012
High Performance 14-Bit, 125MSPS ADC
The ISLA214P12 is a high performance 14-bit 125MSPS analog-to-digital converter offering very high dynamic range and low power consumption. It carries the export control classification number 3A991.c.3 and can be exported without a license to most countries, including China and Russia. It is part of a pin-compatible family of 12- to 16-bit A/Ds with maximum sample rates ranging from 125 to 500MSPS. This allows a design using the ISLA214P12 to accommodate any of the other pin-compatible A/Ds with minimal changes. More
ISL26310
June 2012
12-bit, 125kSPS Low-power ADCs with Single-ended and Differential Inputs and Multiple Input Channels
The ISL26310/11/12/13/14/15/19 family of sampling SAR-type ADCs feature excellent linearity over supply and temperature variations, and offer versions with 1-, 2-, 4- and 8-channel single-ended inputs, and 1-, 2- and 4-channel differential inputs. More
ISL26313
June 2012
12-bit, 125kSPS Low-power ADCs with Single-ended and Differential Inputs and Multiple Input Channels
The ISL26310/11/12/13/14/15/19 family of sampling SAR-type ADCs feature excellent linearity over supply and temperature variations, and offer versions with 1-, 2-, 4- and 8-channel single-ended inputs, and 1-, 2- and 4-channel differential inputs. More
ISL97672B
June 2012
6-Channel LED Driver with Ultra Low Dimming Capability
The ISL97672B is an integrated power LED driver that controls six channels of LED current for LCD backlight applications. The ISL97672B is capable of driving LEDs from 4.5V to 26.5V, with a maximum output of 45V. More
ISL32602E
June 2012
1.8V to 3.3V, Micro-Power, ±15kV ESD, +125°C, Slew Rate Limited, RS-485/RS-422 Transceivers
The Intersil ISL32600E, ISL32601E, ISL32602E and ISL32603E are ±15kV IEC61000 ESD protected, micro power, wide supply range transceivers for differential communication. The ISL32600E and ISL32601E operate with VCC ≥ 2.7V and have maximum supply currents as low as 100µA with both the transmitter (Tx) and receiver (Rx) enabled. The ISL32602E and ISL32603E operate with supply voltages as low as 1.8V. These transceivers have very low bus currents, so they present less than a 1/8 unit load to the bus. This allows more than 256 transmitters on the network, without violating the RS-485 specification’s 32 unit load maximum. More
ISL32603E
June 2012
1.8V to 3.3V, Micro-Power, ±15kV ESD, +125°C, Slew Rate Limited, RS-485/RS-422 Transceivers
The Intersil ISL32600E, ISL32601E, ISL32602E and ISL32603E are ±15kV IEC61000 ESD protected, micro power, wide supply range transceivers for differential communication. The ISL32600E and ISL32601E operate with VCC ≥ 2.7V and have maximum supply currents as low as 100µA with both the transmitter (Tx) and receiver (Rx) enabled. The ISL32602E and ISL32603E operate with supply voltages as low as 1.8V. These transceivers have very low bus currents, so they present less than a 1/8 unit load to the bus. This allows more than 256 transmitters on the network, without violating the RS-485 specification’s 32 unit load maximum. More
ISL32600E
June 2012
1.8V to 3.3V, Micro-Power, ±15kV ESD, +125°C, Slew Rate Limited, RS-485/RS-422 Transceivers
The Intersil ISL32600E, ISL32601E, ISL32602E and ISL32603E are ±15kV IEC61000 ESD protected, micro power, wide supply range transceivers for differential communication. The ISL32600E and ISL32601E operate with VCC ≥ 2.7V and have maximum supply currents as low as 100µA with both the transmitter (Tx) and receiver (Rx) enabled. The ISL32602E and ISL32603E operate with supply voltages as low as 1.8V. These transceivers have very low bus currents, so they present less than a 1/8 unit load to the bus. This allows more than 256 transmitters on the network, without violating the RS-485 specification’s 32 unit load maximum. More
ISL32601E
June 2012
1.8V to 3.3V, Micro-Power, ±15kV ESD, +125°C, Slew Rate Limited, RS-485/RS-422 Transceivers
The Intersil ISL32600E, ISL32601E, ISL32602E and ISL32603E are ±15kV IEC61000 ESD protected, micro power, wide supply range transceivers for differential communication. The ISL32600E and ISL32601E operate with VCC ≥ 2.7V and have maximum supply currents as low as 100µA with both the transmitter (Tx) and receiver (Rx) enabled. The ISL32602E and ISL32603E operate with supply voltages as low as 1.8V. These transceivers have very low bus currents, so they present less than a 1/8 unit load to the bus. This allows more than 256 transmitters on the network, without violating the RS-485 specification’s 32 unit load maximum. More
ISL55163
June 2012
SOC Dual Channel 400MHz Pin Electronics/DAC/PMU
The ISL55163 is a highly integrated System-on-a-Chip (SOC) pin electronics solution aimed at incorporating every analog function, along with some digital support functionality, required on a per channel basis for Automated Test Equipment. The interface, control and I/O of the chip are all digital; all analog circuitry is inside the chip. Two complete tester channels are integrated into each ISL55163. The ISL55163 is pin compatible with Venus4. More
TW3801
June 2012
Security Link Over Coax™ (SLOC™) Transmitter
SLOC™ (Security Link Over Coax) is a transmission protocol for simultaneously transmitting analog CVBS video and digital IP video over a single coaxial cable. More
TW3811
June 2012
Security Link Over Coax™ (SLOC™) Receiver
SLOC™ (Security Link Over Coax) is a transmission protocol for simultaneously transmitting analog CVBS video and digital IP video over a single coaxial cable. More
ISL62771
June 2012
Multiphase PWM Regulator for AMD Fusion™ Mobile CPUs Using SVI 2.0
The ISL62771 is fully compliant with AMD Fusion™ SVI 2.0 and provides a complete solution for microprocessor and graphics processor core power. The ISL62771 controller supports two Voltage Regulators (VRs) with three integrated gate drivers. The Core VR supports 2-, or 1-phase configurations while the Northbridge VR supports 1-phase operation. The two VRs share a serial control bus to communicate with the AMD CPU and achieve lower cost and smaller board area compared with two-chip solutions. More
ISL97691
June 2012
2.4V LED Driver with Independent Analog and PWM Dimming Controls of 2 Backlights for 3D Application
The ISL97691 is Intersil’s highly integrated 4 channel LED driver for single cell Li-Ion battery operated mobile displays requiring analog dimming, and for 3D mobile display applications. It drives four 40mA channels of LEDs up to 26V from an input supply 2.4V to 5.5V. The ISL97691 will also drive 60mA channels up to 21V at 30% duty for high peak current 3D modes. More
ISL1561
June 2012
Fixed Gain Dual Port Class-G Differential xDSL Line Driver
The ISL1561 is a fixed gain dual port class-G differential amplifier designed for driving full rate ADSL2+ and VDSL2 signals at very low power dissipation. The driver runs on a single +14V power supply and internally generates higher supply voltages when needed to enable power efficient operation for high peak-to-average ratio (PAR) ADSL2+ and VDSL2 signals. More
ISL78302A
June 2012
Dual LDO with Low Noise, Very High PSRR and Low IQ
ISL78302A is a high-performance dual LDO capable of sourcing 300mA current from each output. It has a low standby current and very high PSRR and is stable with output capacitance of 1µF to 10µF with ESR of up to 200mΩ. More
ISL26322
June 2012
12-bit, 250kSPS Low-power ADCs with Single-ended and Differential Inputs and Multiple Input Channels
The ISL26320/21/22/23/24/25/29 family of sampling SAR-type ADCs feature excellent linearity over supply and temperature variations, and offer versions with 1-, 2-, 4- and 8-channel single-ended inputs, and 1-, 2- and 4-channel differential inputs. More
ISL26324
June 2012
12-bit, 250kSPS Low-power ADCs with Single-ended and Differential Inputs and Multiple Input Channels
The ISL26320/21/22/23/24/25/29 family of sampling SAR-type ADCs feature excellent linearity over supply and temperature variations, and offer versions with 1-, 2-, 4- and 8-channel single-ended inputs, and 1-, 2- and 4-channel differential inputs. More
ISL26325
June 2012
12-bit, 250kSPS Low-power ADCs with Single-ended and Differential Inputs and Multiple Input Channels
The ISL26320/21/22/23/24/25/29 family of sampling SAR-type ADCs feature excellent linearity over supply and temperature variations, and offer versions with 1-, 2-, 4- and 8-channel single-ended inputs, and 1-, 2- and 4-channel differential inputs. More
ISL26329
June 2012
12-bit, 250kSPS Low-power ADCs with Single-ended and Differential Inputs and Multiple Input Channels
The ISL26320/21/22/23/24/25/29 family of sampling SAR-type ADCs feature excellent linearity over supply and temperature variations, and offer versions with 1-, 2-, 4- and 8-channel single-ended inputs, and 1-, 2- and 4-channel differential inputs. More
ISL7124SEH
June 2012
Single Supply Quad Operational Amplifier
The single-event radiation hardened ISL7124SRH, ISL7124SEH consist of four independent, high gain, internally frequency compensated operational amplifiers, specifically designed to operate from a single power supply over a wide range of voltages. These devices are functionally equivalent to industry standard 124 types, offering improvements in supply current and power supply rejection ratio. More
ISL7119EH
June 2012
High Speed Dual Voltage Comparator
The ISL7119RH is a radiation hardened high speed dual voltage comparator fabricated on a single monolithic chip. It is designed to operate over a wide dual supply voltage range as well as a single 5V logic supply and ground. The open collector output stage facilitates interfacing with a variety of logic devices and has the ability to drive relays and lamps at output currents up to 25mA. More
HS-565BEH
June 2012
High Speed, Monolithic Digital-To-Analog Converter
The HS-565BRH, HS-565BEH are fast, radiation hardened 12-bit current output, digital-to-analog converters. This part replaces the HS-565ARH, which is no longer available. The monolithic chips include a precision voltage reference, thin-film R-2R ladder, reference control amplifier and twelve high-speed bipolar current switches. More
HS-508BEH
June 2012
Radiation Hardened 8 Channel CMOS Analog Multiplexer with Overvoltage Protection
The HS-508BRH, HS-508BEH are dielectrically isolated, radiation hardened, CMOS analog multiplexers incorporating an important feature; they withstand analog input voltages much greater than the supplies. This is essential in any system where the analog inputs originate outside the equipment. They can withstand a continuous input up to 10V greater than either supply, which eliminates the possibility of damage when supplies are off, but input signals are present. Equally important, they can withstand brief input transient spikes of several hundred volts; which otherwise would require complex external protection networks. Necessarily, ON resistance is somewhat higher than similar unprotected devices, but very low leakage current combine to produce low errors. Reference Application Notes 520 and 521 for further information on the HS-508BRH,
HS-508BEH multiplexers in general. More
HS-26CT31EH
June 2012
Quad Differential Line Driver, TTL Enable
The Intersil HS-26CT31RH, HS-26CT31EH are quad differential line drivers designed for digital data transmission over balanced lines and meet the requirements of EIA standard RS-422. Radiation hardened CMOS processing assures low power consumption, high speed, and reliable operation in the most severe radiation environments. More
ISL29120
June 2012
Digital Output, Low Power, Red, Green, and Blue Color Light Sensor
The ISL29120 is a low power, high sensitivity, integrated red, green, and blue light sensor with an I2C (SMBus Compatible) interface. Its state-of-the-art photodiode array provides an accurate red, green and blue spectral response. The ADC is capable of rejecting 50Hz and 60Hz flicker caused by artificial light sources. A selectable range allows the user to optimize sensitivity suitable for the specific application. More
ISL24858
June 2012
15-Channel I2C Programmable TFT-LCD Reference Voltage Generator with Integrated EEPROM, and Ultra-low Power Operation
The ISL24858 is a programmable reference voltage generator for TFT-LCDs featuring ultra-low power operation. The ISL24858 contains an I2C programmable, 10-bit, 14-channel gamma reference voltage generator with buffered outputs, a 10-bit programmable VCOM calibrator, a high output current VCOM amplifier, and internal EEPROM to store all reference voltage data. The EEPROM features an endurance of 10,000 write cycles. More
ISL28617
May 2012
40V Precision Instrumentation Amplifier with Differential ADC Driver
The ISL28617 is a high performance, differential input, differential output instrumentation amplifier designed for precision analog to digital applications. It can operate over a supply range of 8V (±4V) to 40V (±20V) and features a differential input voltage range up to ±34V. The output stage has rail-to-rail output drive capability optimized for differential ADC driver applications. Its versatility and small package makes it suitable for a variety of general purpose applications. Additional features not found in other instrumentation amplifiers enable high levels of DC precision and excellent AC performance. More
ISL9110A
May 2012
1.2A High Efficiency Buck-Boost Regulator
The ISL9110A is a highly-integrated Buck-Boost switching regulator that accepts input voltages either above or below the regulated output voltage. Unlike other Buck-Boost regulators, this regulator automatically transitions between operating modes without significant output disturbance. More
TW6865
May 2012
4-in-1 Video Decoders with PCI Express Media Bridge
The TW6865 is a highly integrated solution that supports multi-channel video and audio capture via PCIe x1 interface for PC DVR system and video analytic application. It contains high quality four channel NTSC/PAL/SECAM video decoders that convert analog composite video signal to digital component YCbCr data, and utilize adaptive 4H comb filter for separating luminance and chrominance to reduce cross noise artifacts. More
ISLA224S12
May 2012
Dual 14-Bit, 125 MSPS JESD204B High Speed Serial Output ADC
The ISLA224S is a series of low-power, high-performance, dual-channel 14-bit, analog-to-digital converters. Designed with FemtoCharge™ technology on a standard CMOS process, the series supports sampling rates of up to 250MSPS. The ISLA224S is part of a pin-compatible family of 12- and 14-bit dual-channel A/Ds with maximum sample rates ranging from 125MSPS to 250MSPS and shares the same analog core as Intersil's proven ISLA224P series of ADCs. The family minimizes power consumption while providing state-of-the art dynamic performance, offering an optimal performance-vspower trade-off. More
ISLA222S12
May 2012
Dual 12-Bit, 125 MSPS JESD204B High Speed Serial Output ADC
The ISLA222S is a series of low-power, high-performance, dual-channel 12-bit, analog-to-digital converters. Designed with FemtoCharge™ technology on a standard CMOS process, the series supports sampling rates of up to 250MSPS. The ISLA222S is part of a pin-compatible family of 12- and 14-bit dual-channel A/Ds with maximum sample rates ranging from 125MSPS to 250MSPS and shares the same analog core as Intersil's proven ISLA222P series of ADCs. The family minimizes power consumption while providing state-of-the art dynamic performance, offering an optimal performance-vs-power trade-off. More
ISLA222S20
May 2012
Dual 12-Bit, 200 MSPS JESD204B High Speed Serial Output ADC
The ISLA222S is a series of low-power, high-performance, dual-channel 12-bit, analog-to-digital converters. Designed with FemtoCharge™ technology on a standard CMOS process, the series supports sampling rates of up to 250MSPS. The ISLA222S is part of a pin-compatible family of 12- and 14-bit dual-channel A/Ds with maximum sample rates ranging from 125MSPS to 250MSPS and shares the same analog core as Intersil's proven ISLA222P series of ADCs. The family minimizes power consumption while providing state-of-the art dynamic performance, offering an optimal performance-vs-power trade-off. More
ISL58797
May 2012
Laser Diode Driver with Write Current DAC and PDIC Control Outputs
The ISL58797 is a highly integrated, single supply laser diode driver designed to support multi-standard writable optical drives in CD, DVD, and Blue Ray formats at various speeds. It is a ‘hybrid’ part having an interface compatible with a conventional LDD, but an internal architecture similar to a write strategy LDD. This combination adds versatility to the conventional interface. The ISL58797 also features PDIC (OEIC) control pins; which help reduce the signal lines on the Flex cables. More
