| |
|
| |
| Digitally Controlled Potentiometer (XDCP™) |
| |
|
| |
| |
|
|
Available in RoHS/Pb-Free
|
|
 Buy direct from Intersil
|
 Check distributor inventory
|
 Request samples
|
|
 |
 |
Part No. |
Design-In
Status |
Temp. |
Package |
MSL |
Price
US $ |
|
|
|
|
|
|
| X93155UM8I |
Active |
Ind |
8 Ld MSOP |
1 |
0.59 |
|  |
 |
|
|
|
| X93155UM8IT1 |
Active |
Ind |
8 Ld MSOP T+R |
1 |
0.59 |
|  |
|
|
|
|
| X93155UM8IZ |
Active |
Ind |
8 Ld MSOP |
2 |
0.59 |
 |
 |
|
|
|
|
| X93155UM8IZT1 |
Active |
Ind |
8 Ld MSOP T+R |
2 |
0.59 |
|
 |
|
|
|
|
| XLABVIEW01 |
Active |
|
|
N/A |
91.77 |
|  |
|
|
|
|
| XLABVIEW01Z |
Active |
|
Eval Board |
N/A |
91.77 |
|
 |
|
|
|
|
| The price listed is the manufacturer's suggested retail price for quantities of 1K units. However, prices in today's market are fluid and may change without notice. |
| MSL = Moisture Sensitivity Level - per IPC/JEDEC J-STD-020 |
| SMD = Standard Microcircuit Drawing |
|
| |
 Description |
|
|
The Intersil X93155 is a digitally controlled potentiometer (XDCP). The device consists of a resistor array, wiper switches, a control section, and nonvolatile memory. The wiper position is controlled by a 3-wire interface.
The potentiometer is implemented by a resistor array composed of 31 resistive elements and a wiper switching network. The position of the wiper element is controlled by the CS, U/D, and INC inputs. The position of the wiper can be stored in nonvolatile memory and then be recalled upon during a subsequent power-up operation. The device is connected as a two-terminal variable resistor and can be used in a wide variety of applications including: - Bias and Gain Control
- LCD Contrast Adjustment
|
| |
 Key Features |
|
|
| |
-
Solid-state potentiometer
-
Up/Down interface
-
32 wiper tap points per potentiometer
-
Wiper position stored in nonvolatile memory and recalled on power-up
-
31 resistive elements per potentiometer
-
Temperature compensated
-
Maximum resistance tolerance ±25%
-
Terminal voltage, 0 to VCC
-
Low power CMOS
-
VCC = 5V ±10%
-
Active current, 200μA typ.
-
Standby current, 2.0μA max
-
High reliability
-
Endurance 200,000 data changes per bit
-
Register data retention, 100 years
-
RTOTAL value = 50kΩ
-
Packages
-
Pb-free available (RoHS compliant) VCC
|
| Related Documentation |
|
|
| |
 Application Note(s): |
|
| |
 Datasheet(s): |
| | |
 Technical Brief(s): |
| | |
 Evaluation Board(s): |
| | |
 Technical Homepage: |
| | | |
| |
 Parametric Data |
| | # of Devices/ Channels | | 1 | | | # of Taps | | 32 | | | Memory Type | | Non-Volatile | | | Bus Interface Type | | 3-Wire (Up/Down) | | | Resistance Options (kΩ) | | 50 | | | VCC Range (V) | | 4.5 to 5.5 | | | VCC (min) (V) | | 4.5 | | | VCC (max) (V) | | 5.5 | | | DCP Single Supply Range (V) | | 0 to 5.5 | | | Resistance Taper | | Linear | | | Wiper Current (mA) | | ±0.6 | | | Wiper Resistance (Ω) | | * | | | Supply Current (μA) | | 2 | | | Max Operating Temp (°C) | | 85 | | | End-to-End Tempco (ppm/°C) | | ±35 | | | Middlepoint Ratiometric Tempco (ppm/°C) | | * | | | VL min. terminal voltage (V) | | 0 | | | VH max. terminal voltage (V) | | 5.5 | | | Features | | 2-terminal - Rheostat mode only | |
|
| |
 Application Block Diagrams |
|
| |
|
| |
|
|
| |
| | ISL22511 | | Single Push Button Controlled Potentiometer (XDCP™), Low Noise, Low Power, 32 Taps, PushButton Controlled Potentiometer | | | | X9313 | | Digitally Controlled Potentiometer (XDCP™), Linear, 32 Taps, 3 Wire Interface, Terminal Voltages ± VCC | | | | X9314 | | Single Digitally Controlled Potentiometer (XDCP™) | | | | X9315 | | Digitally Controlled Potentiometer (XDCP™) | | | | X93154 | | Digitally Controlled Potentiometer (XDCP™) | | | | X93156 | | Single Digitally Controlled Potentiometer (XDCP™), Low Noise, Low Power, 3 wire Up/Down, 32 Taps | | | | X9511 | | Single Digitally-Controlled (XDCP™) Potentiometer (Push Button Controlled) | |
|
